Mercedes 350SL Brake Master Cylinder Parts
Showing 3 out of 3 part(s) found in our catalog.
Brand
Keyword
Subcategory
Mon-Fri 8-4 MST/PST (Arizona Time)
Based on industry averages you can expect to pay between $58.99 and $370.99 for a Mercedes 350SL brake master cylinder.
How Do I Know If My Mercedes 350SL Brake Master Cylinder Is Failing?
A failing Mercedes 350SL brake master cylinder often makes itself known with a few clear warning signs. You might notice the brake pedal feels unusually soft or spongy, or you may find you need to press harder than usual to stop the car. Sometimes the brake warning light will flicker on, or you’ll spot puddles of brake fluid underneath your vehicle or right around the cylinder. If the pedal sinks steadily to the floor when pressed, this often points to an internal leak in the master cylinder. Since this part is essential for safe stopping, any of these symptoms should be checked right away. A quick home test is to hold the brake pedal down—if it keeps sinking rather than holding firm, it’s likely time for a closer look or replacement. Prompt action here is key to keeping your brakes working safely.
What Is The Correct Process For Replacing The Mercedes 350SL Brake Master Cylinder?
Replacing the Mercedes 350SL brake master cylinder starts with a bit of preparation. First, disconnect the negative battery cable for safety, then use a turkey baster or similar tool to remove most of the brake fluid from the reservoir. Carefully disconnect the brake lines at the cylinder using a line wrench, being careful not to strip the fittings. Next, remove the mounting bolts and lift the old master cylinder away from the brake booster. Before installing the new one, bench-bleed it to get rid of trapped air. Set the new master cylinder in place, secure it with the bolts, and reconnect the brake lines. Once everything’s tight, fill the reservoir with fresh brake fluid and bleed the entire brake system, starting at the wheel farthest from the master cylinder and working closer. Check for leaks and be sure the pedal feels solid before heading out on the road.
How Can I Properly Bleed Air From The Brake System After Changing The Master Cylinder?
After installing a new Mercedes 350SL brake master cylinder, bleeding out the air is a must for safe braking. Pour fresh brake fluid into the reservoir, then either grab a helper for the classic two-person method or use a vacuum bleeder. If you’re working with a partner, one person pumps the brake pedal while the other opens the bleeder screws at each wheel, starting with the one farthest away. Continue until you see a steady flow of clear, bubble-free fluid, topping off the reservoir often to keep new air from sneaking in. Repeat this at each wheel. If the pedal still doesn’t feel firm after one round, don’t be afraid to bleed the system again until it’s just right.
What Brake Fluid Should I Use In My Mercedes 350SL Brake Master Cylinder?
For your Mercedes 350SL brake master cylinder, the recommended choice is DOT 4 brake fluid. Always double check your owner’s manual to make sure, but DOT 4 is standard thanks to its higher boiling point and reliability under heat. Don’t mix DOT 4 with other types like DOT 3, DOT 5, or DOT 5.1, as mixing can cause everything from weakened brakes to system damage. When topping off or replacing brake fluid, use a fresh, sealed container and avoid any water or dirt getting inside—the tiniest bit of contamination can cause big problems down the road.
Why Am I Still Experiencing A Soft Brake Pedal After Changing The Master Cylinder?
Even after swapping in a new Mercedes 350SL brake master cylinder, a soft brake pedal typically points to air stuck somewhere in the system. It’s possible bleeding needs to be done a second (or even third) time, especially if air was trapped during installation, or if the master cylinder didn’t get bench-bled first. Another common culprit is a leak along the brake lines, fittings, or even at one of the calipers. Old, flexible brake hoses can also make the pedal feel soft as they expand under pressure. Double check all connections and look for any damp spots or drips under the car. Sometimes, even with new parts, a defective master cylinder might sneak through—so if you’ve checked everything else, it could be worth testing the new part.
How Can You Easily Get A Mercedes 350SL Brake Master Cylinder?
Shopping at AutohausAZ makes finding your Mercedes 350SL brake master cylinder much easier. You’ll get great prices and fast shipping, so you’re not left waiting for your part to arrive. If something’s not quite right, returns are a breeze. We’re here to help you save money and time with every order, so your repairs get done with as little hassle as possible.
