Mercedes 420SEL Brake Master Cylinder Parts

Showing 1 out of 1 part(s) found in our catalog.

Narrow Down Your Search By...
Filter search results specific to your vehicle.
Keyword
Keyword
Mercedes 420SEL
Category
Brake
Subcategory
Brake Master Cylinder
Subcategory
Can't Find What You Need?
Mon-Fri 8-4 MST/PST (Arizona Time)
Contact Us
Sort By:
1986, 1987, 1988, 1989, 1990, 1991 Mercedes 420SEL
Ships Today
Ships Today Information Icon
Leaves closest warehouse today if ordered before 2 PM MST.
$90.99
Reg
$94.78
List
$268.00

The average price of a Mercedes 420SEL brake master cylinder is between $90.99 and $90.99.

What Are The Signs Of A Failing Mercedes 420SEL Brake Master Cylinder?

When your Mercedes 420SEL brake master cylinder begins to fail, you’ll usually notice a few telltale signs. The brake pedal might start to feel spongy or sink lower than normal when you press it, and it may take longer than usual for your car to come to a stop. It’s also common to see brake fluid leaking underneath the hood or beneath the car, hinting that the brake master cylinder is losing pressure. Other red flags include diminished braking power or a brake warning light lighting up on your dashboard. If you notice any of these symptoms, it’s important to check the Mercedes 420SEL brake master cylinder as soon as possible to avoid losing braking ability. Handling these problems early helps keep your brakes working reliably and makes sure you stay safe on the road.

How Do I Replace The Mercedes 420SEL Brake Master Cylinder?

To put in a new Mercedes 420SEL brake master cylinder, start by disconnecting the battery and relieving pressure in the brake system. Carefully unbolt and remove the brake lines attached to the cylinder—be ready with something to catch any leaking fluid. Take out the old master cylinder from where it’s mounted on the brake booster or firewall. Before installing the new brake master cylinder, it’s a good idea to bench-bleed it to remove air. Fit the new cylinder in place, connect the brake lines again, and fill the reservoir with fresh brake fluid. Bleed the brakes at all four wheels to make sure you get a firm pedal and smooth operation. Finally, check for leaks and make sure everything is tight before driving.

What Type Of Brake Fluid Should Be Used With The Mercedes 420SEL Brake Master Cylinder?

Your Mercedes 420SEL brake master cylinder works best with DOT 4 brake fluid, as recommended by the manufacturer. This fluid type keeps the right balance of viscosity and boiling point, which is important to avoid moisture buildup or vapor lock. Always use new, unopened brake fluid to minimize the risk of contamination. Before pouring in the fluid, it’s smart to double-check with the owner’s manual, since using the wrong type can affect brake performance or damage seals. Sticking with the right brake fluid helps your brakes stay responsive and trustworthy for the long run.

What Causes The Mercedes 420SEL Brake Master Cylinder To Leak?

A leaking Mercedes 420SEL brake master cylinder is often caused by worn-out internal seals or corrosion inside the cylinder bore. Over time, the rubber seals naturally break down due to age, heat, and repeated exposure to brake fluid, eventually allowing fluid to seep out. Using old or contaminated fluid can speed up this process by introducing moisture, which causes rust and pitting that damage the seal. If you spot brake fluid around the master cylinder, under the reservoir, or running down the booster, the part is likely on its way out. Usually, the best solution is to replace the brake master cylinder completely rather than try a repair.

Do I Need To Bleed The Brakes After Replacing The Mercedes 420SEL Brake Master Cylinder?

Yes—after swapping the Mercedes 420SEL brake master cylinder, bleeding the brakes is a must. Removing and installing the cylinder can let air into the brake lines, which makes the pedal feel soft or unsteady. Properly bleeding all four wheels gets rid of trapped air, restoring brake pressure and bringing back that confidence-inspiring pedal feel. Skipping this step means the repair won’t do its job, and your brakes may not function safely. Always check the fluid level after bleeding, and top it off with DOT 4 fluid if needed so your car’s ready for the road.

Why Choose AutohausAZ For Your Mercedes 420SEL Brake Master Cylinder?

AutohausAZ makes getting a Mercedes 420SEL brake master cylinder simple and stress-free. Their pricing is straightforward, so you always know you’re getting a fair deal. Shipping moves quickly, meaning you won’t be stuck waiting long to get back on the road. And if you ever need to make a return, the process is hassle-free. Shopping here means less time worrying and more time driving your Mercedes where it belongs.