Mercedes E500 Camshaft Position Sensor Parts
Showing 4 out of 4 part(s) found in our catalog.
Brand
Keyword
Subcategory
Mon-Fri 8-4 MST/PST (Arizona Time)
The average price of a Mercedes E500 camshaft position sensor is between $4.89 and $38.99.
What Are The Symptoms Of A Failing Mercedes E500 Camshaft Position Sensor?
If your Mercedes E500 camshaft position sensor starts to fail, the engine mood shifts fast. One day it’s smooth, the next, it's stumbling through traffic. Misfires sneak in, idle gets lumpy, and stalling crops up right in the middle of your commute. Sometimes, the car hesitates to start—especially after you run into a store and come back to a warm engine. A glowing check engine light only adds to the distraction. These problems can sneak up, but if you ignore them, they grow. You might find your E500 refusing to start at all. Most of the time, swapping out the Mercedes E500 camshaft position sensor turns things around fast.
How Do You Diagnose A Faulty Mercedes E500 Camshaft Position Sensor?
Start with a scan tool. Plug it in, and look for codes like P0340—almost always tied to the camshaft position sensor. Pop the hood, and check the wiring and connectors near the sensor. Oil and dirt build up over time, so any green corrosion or frayed wires are red flags. Want to go deeper? Check the signal with a multimeter, though not everyone feels comfortable poking around electrical stuff. If you clear the codes and they return, or if new symptoms creep up, swapping the sensor is often the simplest fix. Don’t skip checking for stretch in the timing chain before you order the part.
Where Is The Mercedes E500 Camshaft Position Sensor Located?
You’ll find the Mercedes E500 camshaft position sensor either at the front or rear of the engine, but most E500 models have it on the passenger side, close to the valve cover. Peek behind the intake tubes—look for a stubby sensor with a small bolt holding it down and a plug snapped into it. Sometimes, the engine cover needs to come off first. Once you spot it, the swap only needs basic hand tools and a bit of patience.
What Causes The Mercedes E500 Camshaft Position Sensor To Fail?
Heat is the big villain here—under that hood, temps stick around at numbers that make electronics sweat. Oil leaks add to the challenge, sometimes creeping into the sensor and causing shorts. Wiring ages, plugs get brittle, and vibrations don't help. Some sensors hang in there for years, others give up early, especially with poor engine seals or neglected maintenance. Fix leaks early, and your camshaft position sensor usually hangs in much longer.
How Do You Replace The Mercedes E500 Camshaft Position Sensor?
First, unhook the negative battery cable. Next, track down the sensor beside the valve cover and unscrew its mounting bolt. Pull the electrical plug free—sometimes the clip fights you. Wiggle the old sensor loose if oil makes it sticky. Before you slot in the new one, wipe the area clean. Slide the new Mercedes E500 camshaft position sensor in, bolt it in place, and reconnect the harness. Tighten things snug, not too hard. Reconnect the battery, clear any lingering codes, and take the car for a drive to see how it responds.
Why Buy Your Mercedes E500 Camshaft Position Sensor From AutohausAZ?
Buying parts shouldn’t be a hassle, and at AutohausAZ, we get that. People come here looking for honest prices without the drama. We cut out the middleman, so you don't end up paying more for the same sensor that keeps your E500 running right. Our shelves stay stocked, orders go out fast, and tracking keeps you in the loop. Life’s busy—you want your car back on the road, not tied up in shipping limbo.
Nobody enjoys returns, but sometimes it happens. We keep it simple so you don’t lose time. If the part isn’t right, swapping it out takes just a few clicks. Need help? Our support team answers questions and keeps things smooth. When you shop AutohausAZ, you get value, speed, and confidence in every order. Nothing fancy—just solid service and real savings.
