Mercedes E550 Camshaft Position Sensor Parts
Showing 8 out of 8 part(s) found in our catalog.
Brand
Keyword
Subcategory
Mon-Fri 8-4 MST/PST (Arizona Time)
Based on industry averages you can expect to pay between $4.89 and $47.99 for a Mercedes E550 camshaft position sensor.
What Are The Symptoms Of A Failing Mercedes E550 Camshaft Position Sensor?
A failing Mercedes E550 camshaft position sensor tends to make itself known in a few different ways. Maybe you notice the engine doesn’t idle like it used to—there’s a little shaking, a bit of wandering. Sometimes you press the gas pedal and the car hesitates or jerks. Misfires can sneak up on you, and out of nowhere, the car may stall in traffic or when you’re stopped. Starting the car can get tricky too; the engine might crank longer than normal or refuse to fire up altogether. Often, the check engine light flips on with a code mentioning camshaft timing or position. At first, this can happen once in a while. If ignored though, things tend to get worse and more frequent. Catching these signs early often saves you from bigger headaches down the road.
How Do I Replace The Mercedes E550 Camshaft Position Sensor?
First, pop the hood and disconnect the battery. Track down the Mercedes E550 camshaft position sensor; it sits on the cylinder head, tucked behind the engine cover or near the timing gear. Pull the connector free, take out the bolt holding the sensor, and ease the old one out. Line up your new sensor, set it in place, and tighten the bolt—don’t overdo it. Plug in the connector, double check that it’s snug, and reconnect your battery. Clear any check engine codes with a scanner if you have one. Fire up the engine to see that everything runs smooth. No long cranking, no warning lights, no fuss.
Where Is The Mercedes E550 Camshaft Position Sensor Located?
The Mercedes E550 camshaft position sensor usually hides at one end of the cylinder head. Sometimes you find it up front; other times, it’s at the rear closer to the firewall. You’ll likely need to pull off a plastic engine cover to get a clear look. It’s a small sensor, mounted with a single bolt, connected by a wiring pigtail. Look near the intake manifold side—right by the cam gear in many models. If you’re hunting around and not sure, check your owner’s manual for a diagram that points it out. Don’t mix it up with the crankshaft sensor, since both hide in crowded engine bays.
What Causes A Mercedes E550 Camshaft Position Sensor To Fail?
Heat gets to everything under a hood, and the Mercedes E550 camshaft position sensor is right in the thick of it. Years of sitting near hot cylinder heads bakes the wiring and breaks down the plastic. Old gaskets can leak oil into the connector, and that sticky mess causes shorts and electrical trouble. Sometimes vibration rattles the wiring loose, or corrosion sneaks in at the plug. Even something as random as a hiccup in the assembly line can set up future failure. Keeping the area clean and dry, and fixing oil leaks fast, gives your sensor a longer, healthier life.
Do I Need To Reprogram Anything After Replacing The Camshaft Position Sensor?
Usually, no reprogramming is needed after replacing the Mercedes E550 camshaft position sensor. Most times, the car’s computer will pick up the new part on its own. You should clear any fault codes using a scan tool, just to keep the dashboard clean. Take the car for a short drive and watch for warning lights—most problems vanish after a proper fix. If something still feels off or the codes come back, it’s time for a closer look by a pro. But in most cases, swap the part, clear the code, and drive on.
Need A Reliable Mercedes E550 Camshaft Position Sensor?
At AutohausAZ, we know how much our customers care about keeping their Mercedes E550 running smoothly. That’s why we work hard to offer quality parts, like the Mercedes E550 camshaft position sensor, at prices that won’t shock you. We keep our selection extensive so you can find the right sensor without bouncing from site to site. When you place your order, you get more than savings—you also get some of the fastest shipping around. Nobody wants to wait days to get their car running again, so we make sure our team hustles to get your order out the door, right here from our Phoenix warehouse. And if you ever end up with the wrong part, you won’t get the runaround trying to send it back. Our easy returns process is straightforward and hassle-free, giving you one less thing to worry about. We’re car people ourselves, so we get how frustrating downtime can be. That’s why we’re always focused on providing clear information, honest pricing, and real support. Whether you’re a weekend DIYer or a pro wrenching for a living, we want you to shop knowing you’ve got our team on your side. At AutohausAZ, stocking the right camshaft position sensor for your E550—and making your life easier—is what drives us.
