VW Fastback Valve Cover Parts
Showing 1 out of 1 part(s) found in our catalog.
Brand
Keyword
Subcategory
Mon-Fri 8-4 MST/PST (Arizona Time)
Based on industry averages you can expect to pay between $9.99 and $9.99 for a VW Fastback valve cover.
What Is The Best Gasket Material For A VW Fastback Valve Cover?
Choosing a gasket for your VW Fastback valve cover can get confusing, but most people reach for cork first. Cork gaskets work well because they squish into the small imperfections on the cover and create a tight seal, especially if you dab on a bit of sealant. Rubber gaskets last a long time and don't mind heat or oil, but they can be tricky if the cover isn’t really flat—sometimes they just don't want to sit right. Some new sets mix cork and rubber, and those often hit a good balance of flexible and strong. No matter what you pick, clean up the surfaces well before you start. That’s half the battle to keeping your VW Fastback valve cover from leaking.
How Do You Stop Oil Leaks On A VW Fastback Valve Cover?
Oil streaking down from your VW Fastback valve cover? You’re not alone. Start by checking if the cover is bent or has worn corners. Give the edges and cylinder head a good scrub to get rid of old gasket bits, grimy oil, and dirt. Swap in a new gasket every time—don’t cheap out and reuse the old one. A thin bead of sealant on both sides of the gasket can help, but don’t slather it on or you’ll plug up oil paths. When you tighten the bolts, go slow and alternate sides to keep things even. Keep an eye on it for a few drives, since sometimes the hardware needs a little re-tightening as things settle.
How Tight Should The Valve Cover Bolts Be On A VW Fastback?
It’s tempting to crank down on the VW Fastback valve cover bolts. But that usually ends in trouble—stripped threads, cracked covers, and gaskets that get crushed right out of place. You want them just tight enough to squish the gasket, but not so tight it gets smashed flat. Use a crisscross pattern as you go, and if you’ve got a small torque wrench, aim for five to seven foot-pounds. Most times, just using a small wrench and a tug about as firm as you’d use tightening a spark plug does fine. Check that the gasket looks like it’s making contact all the way around without squeezing out the sides.
What Causes The Valve Cover On A VW Fastback To Keep Coming Loose?
If your VW Fastback valve cover won’t stay put, look at the bolts first – they might be stripped out or stretched. Sometimes the cover itself is just a little warped, which makes it impossible to keep it snug. An old, tired gasket can also compress too much and the bolts loosen up. Replace the hardware if it’s questionable, and always use a good, fresh gasket. Make sure you’re using the crisscross method to tighten, instead of going in a circle. Check the bolts again after your next ride or two, since brand-new gaskets can settle after some heat and leave things loose again.
Can You Reuse The Valve Cover Gasket On A VW Fastback?
Even if it looks like it could work, reusing a VW Fastback valve cover gasket usually means signing up for another leak. Once a gasket’s been smashed down, soaked, and baked, it just won’t seal right again. Always swap in a new one when you pull the cover off. Clean both surfaces as much as possible and check to see that the edge of the cover is straight. That little bit of effort each time saves you from hours chasing drips later on.
Looking For The Best VW Fastback Valve Cover?
When you’re hunting for a VW Fastback valve cover, AutohausAZ keeps it simple. Good prices, quick shipping, and no-stress returns mean you don’t waste your time or money. Quality parts and old-school service let you focus on driving, not worrying. Pick the right part, get it delivered fast, and get back to your project.
