BMW 128i Brake Pad Sensor Parts
Showing 11 out of 11 part(s) found in our catalog.
Brand
Keyword
Subcategory
Mon-Fri 8-4 MST/PST (Arizona Time)
Based on industry averages you can expect to pay between $7.89 and $26.99 for a BMW 128i brake pad sensor.
A BMW 128i brake pad sensor is a safety device installed within the braking system of a BMW 128i vehicle. It plays a crucial role in alerting the driver when the brake pads have worn down to a certain level and need to be replaced. It works by creating an electrical circuit that gets broken once the brake pads wear down to a minimum level. This triggers a warning light on the dashboard, indicating the time for brake pad replacement. Not only does it help maintain optimal brake performance, but it also prevents potential damage to the brake rotors from worn-down brake pads.
The BMW 128i usually comes equipped with two brake pad sensors, one for the front brakes and one for the rear brakes.
Replacing Brake Pad Sensors On A BMW 128i
- Purchase the correct brake pad sensor for your BMW 128i. It's crucial to use genuine parts or high-quality replacements that are designed specifically for your car model.
- Park the car on a flat surface and apply the parking brake. For safety reasons, you might also want to use wheel chocks to prevent the car from moving.
- Use a jack to lift up the car, then use jack stands to secure it. Never rely on just the jack to support the car while you're working.
- Remove the wheel. To do this, loosen the lug nuts with a wrench before lifting the car, then fully remove them and the wheel after the car is lifted.
- Locate the brake pad sensor. It's typically attached to the brake pad itself.
- Unclip the sensor from the brake pad. The sensor is held in place by a small clip. Be careful not to damage this clip, as you'll need it when you install the new sensor.
- Disconnect the sensor wire from the connector. The connector is usually located somewhere along the wheel well. Press down on the small tab on the connector while pulling it apart.
- Connect the new sensor to the connector. Make sure the connection is secure.
- Clip the new sensor onto the brake pad. Again, be careful not to damage the clip.
- Reinstall the wheel. Tighten the lug nuts as much as possible while the car is still lifted, then lower the car and finish tightening them.
- Check the brake pad sensor indicator on your dashboard. If it's not lit, the sensor is working correctly. If it is lit, there may be a problem with the sensor or the installation.
- Repeat the process on the other wheels if necessary. While not always required, it's often a good idea to replace brake pad sensors in pairs.
Top BMW 128i Brake Pad Sensor Brands for Sale
Bowa is a well-established brand associated with the manufacturing of high-quality automotive parts. It boasts decades of commitment to high caliber innovation in the wake of assorted consumer needs. With regards to the BMW 128i brake pad sensor, Bowa exhibits distinct expertise, harnessing the latest technology in the design and production of these components. Bowa seeks to guarantee customer satisfaction through their durable and efficient sensors that continue to gain traction in the market.
Genuine BMW, on the other hand, is a prestigious brand that symbolizes luxury and superior performance. As a brand directly affiliated with the vehicle manufacturer, Genuine BMW parts are renowned for their high quality and reliability, and their brake pad sensors for the BMW 128i are not an exception. The company holds its manufacturers to the highest standards, ensuring all parts, including brake pad sensors, are of impeccable, original equipment quality. Though they tend to be more expensive, the quality and durability of Genuine BMW parts make the additional cost worthwhile to many drivers.
Febi is another reputable company known for manufacturing a wide variety of automotive parts, including BMW 128i brake pad sensors. A hallmark of Febi’s product offerings is their blend of quality and affordability. Febi engages advanced techniques and stringent quality control measures to produce reliable and long-lasting brake pad sensors for BMW 128i models. Their products are a common choice for drivers seeking a balance between cost effectiveness and product quality.
Find Great Deals on BMW 128i Brake Pad Sensor
At AutohausAZ, we pride ourselves on offering quality and reliable BMW 128i brake pad sensors. One of the biggest advantages of shopping with us is the availability of a wide array of options. We understand that every car needs are different, and that's why we provide multiple choices for our customers to choose from.
We also consider affordability a high priority. Our competitive pricing ensures that you get the best deal on your brake pad sensor without compromising on its quality.
Furthermore, our customer support service is excellent. Whether you need help finding a specific part, have questions about installation or encounter any issues, our professional team is always there to assist you.
At AutohausAZ, we also strive to make the shopping process as easy and convenient as possible. From an easy-to-navigate website to detailed product descriptions and clear pricing, we aim to make your shopping experience seamless and enjoyable.
To add to it, we ensure the authenticity of all our products. You can shop with confidence knowing that you're getting genuine, high-quality parts that will serve their purpose reliably.
Lastly, but certainly not least, is the commitment to fast delivery. We understand the urgency that comes with replacing car parts, and we do our best to get your BMW 128i brake pad sensor to you as quickly as possible.
In conclusion, by choosing to shop at AutohausAZ, you're opting for quality, affordability, great customer service, convenience and peace of mind. It’s these advantages that set us apart from the competition.
