BMW 325 Brake Pad Sensor Parts
Showing 5 out of 5 part(s) found in our catalog.
Brand
Keyword
Subcategory
Mon-Fri 8-4 MST/PST (Arizona Time)
BMW 325 brake pad sensor typically cost between $3.29 and $26.29.
A BMW 325 brake pad sensor is a device designed for the car's braking system. It's function is essentially to alert the driver when the brake pads have worn down to a critical level and need replacement. This part plays a vital role in vehicle safety because it provides a warning before the brake pads become too thin, which could compromise the effectiveness of the brakes.
When the brake pads wear down to the sensor, it completes a circuit that turns on a warning light on the vehicle's dashboard. This gives the driver ample time to schedule maintenance and replace the brake pads before they become dangerously thin. It's an essential aspect of maintaining the performance and safety of your BMW 325.
A BMW 325 typically has two brake pad sensors - one located in the front and the other in the rear.
Replacing Brake Pad Sensors On A BMW 325
- Place the car on a level surface and engage the parking brake for safety.
- Use a lug wrench to loosen the lug bolts on the wheel where you'll be replacing the sensor. Don't remove them completely yet.
- Use a jack to lift the car, then place it securely on jack stands. Only then should you fully remove the lug bolts and the wheel itself.
- Once the wheel is out of the way, locate the brake pad wear sensor. This small device will be attached to one of the brake pads, with a wire leading back towards the car's main body.
- Carefully unclip the sensor from the brake pad. Be careful not to damage the brake pad or surrounding components.
- Trace the wire back to the plug that connects it to the car's electrical system. Unplug this carefully, ensuring you don't strain or damage any nearby wires.
- Take your new brake pad sensor and plug it into the same socket. Make sure it clicks in securely.
- Clip the other end of the sensor back onto the brake pad, in the same location as the old sensor.
- Reattach the wheel, tightening the lug bolts as much as possible by hand. Lower the car from the jack stands using the jack.
- Finally, go around the car and tighten all lug bolts with the wrench. Make sure you do this in a cross pattern to ensure even pressure on the wheel.
- Test out your work by driving slowly and testing your brakes. If the warning light on your dashboard goes off, the sensor has been replaced correctly.
- If the light stays on, go back and check your work. If it still doesn't go off, there may be another issue which needs professional attention.
Top BMW 325 Brake Pad Sensor Brands for Sale
BMW 325 brake pad sensor: Genuine BMW is the manufacturer that earns the trust of car enthusiasts due to its record of producing original equipment quality parts. As the OEM (Original Equipment Manufacturer), Genuine BMW has a unique advantage in terms of its extensive knowledge and experience with their vehicles' engineering design. Consequently, these brake pad sensors are meticulously produced to match the exact specifications of the BMW 325 model, ensuring optimum performance, reliability, and a seamless fit. However, as they are branded under the vehicle manufacturer's name, they tend to command a higher price point.
Pex is another prominent name in the brake pad sensor manufacturing industry. It's a European company known for producing high-quality automotive parts with affordability in mind. Pex's brake pad sensors for BMW 325 have gained traction due to the quality materials used and their innovative designs. They are built to meet or even exceed OEM standards, thus ensuring durability and long-lasting performance. Pex brings an enticing mix of value and quality, ideal for those who seek reliable alternatives without compromising their budget.
Febi, on the other hand, is globally recognized for its comprehensive range of spare parts in OE matching quality. With a history that spans over 170 years, Febi has managed to supply brake pad sensors that match the precise requirements of the BMW 325. Known for rigorous quality control checks, Febi parts ensure compatibility, excellent performance, and endurance. These products offer an excellent balance between quality and cost, making them a preferred choice for many BMW owners.
Find Great Deals on BMW 325 Brake Pad Sensor
At AutohausAZ, we pride ourselves on providing high-quality products. Our BMW 325 brake pad sensor is no exception. One of the main advantages of shopping with us is our access to a wide variety of parts. This selection ensures that whatever the need, we have the right part available.
Another advantage is our competitive pricing. We understand that car maintenance can be expensive; hence, we strive to provide affordable solutions to our customers without compromising on quality.
We also value authenticity. All our parts, including the BMW 325 brake pad sensor, are OEM (Original Equipment Manufacturer) or equivalent. This means our customers can rest assured knowing they are buying genuine and original parts that will ensure longevity and optimal performance.
We are committed to excellent customer service. Our team is always ready and willing to assist in any way possible, from helping customers find the correct part to answering any questions they may have about installation or maintenance.
Finally, our user-friendly website makes shopping easy and convenient. Customers can easily find and order the parts they need, with clear descriptions and images for every product.
So, for all these reasons and more, choosing to shop at AutohausAZ for your BMW 325 brake pad sensor and other auto parts needs is a decision you won't regret. It's not just about buying a part; it's about joining a community where quality, affordability, service and convenience are our main priorities.
