BMW 335XI Camshaft Position Sensor Parts
Showing 4 out of 4 part(s) found in our catalog.
Brand
Keyword
Subcategory
Mon-Fri 8-4 MST/PST (Arizona Time)
The average cost of a BMW 335XI camshaft position sensor is between $4.89 and $58.99.
What Are The Common Symptoms Of A Failing BMW 335xi Camshaft Position Sensor?
When the BMW 335xi camshaft position sensor starts to go bad, people usually notice the engine running rough or feeling sluggish. You might get hesitation when you try to accelerate, or you notice the car stumbles during a drive. Sometimes, starting the engine gets harder, especially after the engine’s been running a while. The check engine light comes on pretty often. The car might surprise you with random misfires or shifting that doesn’t make sense. Fuel economy isn’t as good. If the sensor gets too bad, the engine might stall or not start at all, which is tough if you’re relying on your car. Swapping out the sensor normalizes how the car runs most of the time.
Where Is The BMW 335xi Camshaft Position Sensor Located?
You’ll find the BMW 335xi camshaft position sensor as a small device near the cylinder head, usually at the front or side of the engine. Some years put it closer to the timing cover. To reach it, you often have to remove the plastic engine cover and, if you have a turbocharged model, maybe even an intake pipe. The spot can be tight, so it helps to check your service manual before starting. A quick look at the engine—just to see what’s in the way—makes a big difference before you grab your tools.
How Do You Replace A BMW 335xi Camshaft Position Sensor?
Most people with a few tools can handle replacing the BMW 335xi camshaft position sensor themselves. Disconnect the battery to play it safe. Next, pull off any plastic covers, and push aside hoses or pipes that block your reach. Once you spot the sensor, unplug its connector and remove the bolts or screws holding it. Slide the sensor out—don’t yank on the wires. Take the new sensor, fit it in the same spot, and put the bolts back. Reconnect the plug and the battery, then clear any fault codes with a scanner if you have one. Take the car for a short drive to make sure everything feels right.
What Causes The BMW 335xi Camshaft Position Sensor To Fail?
A BMW 335xi camshaft position sensor can fail for many reasons. Heat from the engine can wear down the electronics and casing over time. Tiny oil leaks sometimes drip onto the sensor, causing it to short out or corrode inside. Sometimes, connectors and wiring get dirty, brittle, or damaged, breaking the sensor’s signal. After years and miles, sensors just break down on their own. Staying on top of oil leaks and checking wiring helps, but some sensors just give out as the car gets older.
Can A Bad BMW 335xi Camshaft Position Sensor Cause Other Engine Problems?
A broken BMW 335xi camshaft position sensor can cause more trouble than most folks expect. Not only does it make the check engine light pop up, but it also throws off timing, leading the car to idle rough or shift in ways that don’t feel right. The engine might drink more fuel to make up for the bad signal. If left alone, the problem sometimes puts the engine in limp mode—barely running to prevent damage. If the sensor stays bad, it can cause extra wear on other parts, including the timing system, and sometimes leads to breakdowns out on the road.
Why Choose AutohausAZ For Your BMW 335xi Camshaft Position Sensor?
Shopping at AutohausAZ isn’t just about picking up a BMW 335xi camshaft position sensor. It’s about getting the part you need, faster and without the fuss—no endless searching, no shocking prices. The cost is always low, and most orders get out the door without much delay because we know you want to fix your car and move on. If you ever need to send a part back, it’s as simple as you’d hope—no runaround, just a return. Our team is ready to help if you hit a snag along the way. Car repairs shouldn’t be a hassle. With us, it’s just easier, friendlier, and you can count on the savings.
