Porsche 993 Tail Light Parts
Showing 5 out of 5 part(s) found in our catalog.
Brand
Keyword
Category
Select category below to view parts.
Mon-Fri 8-4 MST/PST (Arizona Time)
Based on industry averages you can expect to pay between $2.19 and $534.99 for a Porsche 993 tail light.
How Do You Remove A Porsche 993 Tail Light Assembly?
To remove a Porsche 993 tail light assembly, start by opening the trunk and moving aside any carpeting or trim near the tail light area. You'll spot a few plastic panels that need to come off—these usually pop out with gentle pressure. Once the panels are out of the way, look for the nuts holding the tail light in place. These are accessible from inside the trunk. Carefully undo them, then gently wiggle the assembly free from the body. Be mindful of the gasket and any attached studs so nothing gets damaged. Don’t forget to disconnect the wiring harness before pulling the unit all the way out. Take note of how bulbs are arranged so putting things back together is a breeze. Once you're done, double check that everything works before fitting everything back together.
What Are The Common Causes Of Porsche 993 Tail Light Failure?
If your Porsche 993 tail light is acting up—maybe flickering, going dim, or not working at all—it’s often due to worn-out bulb sockets, corroded contacts, old bulbs, or a wiring issue. Sometimes moisture sneaks in past an old seal, causing corrosion and spotty electrical contact. Now and then, a bad control module or a poor ground can be the culprit too. Start by taking out the bulbs and checking them, looking for any obvious problems. Give connectors and sockets a close look for build-up or corrosion. Cleaning or swapping out tired parts and making sure everything is dry and snug usually gets your lights shining again.
Can I Upgrade My Porsche 993 Tail Light To LEDs?
Swapping your Porsche 993 tail light over to LED is a popular move these days. There are plenty of LED kits that fit right into your original housings. You’ll get brighter lights and a more modern look. Most of the time, installation is simple, though you might need to add load resistors to stop any dashboard warnings or fast blinking. Just make sure any LEDs you buy are legal for road use where you live. Double check that your car’s wiring can handle the new setup for peace of mind. Done well, an LED upgrade brightens up the rear end and gives the car a fresh touch.
How Do You Fix Tail Light Condensation Or Water Leaks?
It’s not uncommon to find moisture or fogging in a Porsche 993 tail light. Usually, the problem stems from old or cracked gaskets and seals around the housing. Remove the tail light, dry everything thoroughly, and check for cracks or breaks in the gasket and lens. Clean up the contact points, and if the gasket looks worn, either replace it or add a thin bead of silicone sealant to keep water out. If the lens itself is damaged, a new unit may be your only option. Keeping everything sealed up is important for making sure your lights work well and last.
How Do You Replace Bulbs In A Porsche 993 Tail Light?
To change out a bulb in the Porsche 993 tail light, get into the trunk and remove any trim covering the back of the assembly. You'll have access to the bulb sockets—these usually come out with a gentle twist. When installing new bulbs, try not to touch the glass part with your fingers, as that can cause them to burn out faster. After you pop in the new bulb, test all the lights (brake, reverse, and turn signal) before buttoning everything back up. Make sure the trim goes on straight and all fasteners are secure.
Looking For An Affordable Porsche 993 Tail Light?
AutohausAZ makes it easy to pick up a Porsche 993 tail light without breaking the bank. You get fair prices, quick shipping, and a straightforward returns process if anything isn’t right. Whether you’re replacing a broken part or sprucing up your car’s look, shopping here helps you get what you need with less hassle.
