BMW 745i Brake Pad Sensor Parts
Showing 4 out of 4 part(s) found in our catalog.
Brand
Keyword
Subcategory
Mon-Fri 8-4 MST/PST (Arizona Time)
Based on industry averages you can expect to pay between $9.79 and $26.99 for a BMW 745i brake pad sensor.
A BMW 745i brake pad sensor, just like on any other vehicle, is an integral part of the braking system. It's a small device that's attached to the brake pads. Its primary function is to monitor the thickness or wear level of the brake pads.
When the pads wear down over time, the sensor gets tripped and sends a signal to your car's computer. This then triggers a warning light on your dashboard indicating that it's time to replace the brake pads.
This kind of alert system is crucial to maintaining the safety and effectiveness of your braking system. Without it, you might not be aware that your brake pads are wearing thin until it's too late, which could lead to brake failure and potential accidents.
A BMW 745i usually has two brake pad sensors - one for the front and one for the rear.
Replacing Brake Pad Sensors On A BMW 745i
- Start with ensuring that your car is parked on a flat surface and your parking brake is engaged for safety measures.
- Gather all necessary tools and new brake pad sensors for your BMW 745i.
- Use a jack to raise the side of the car where the sensor replacement will take place. Ensure that you place the jack stands under the car for additional stability.
- Begin by removing the wheels using a lug wrench. Once the wheel is off, you can see the brake assembly clearly.
- Locate the brake pad wear sensor, which is usually attached to the brake pad itself. Disconnect the sensor from its connector, being careful not to damage any other parts.
- After successfully disconnecting the old sensor, it's time to install the new one. Carefully thread the new sensor through the same path that the old one followed.
- Connect the new sensor to the brake pad, ensuring it's secure. Afterward, fix it into the brake system's wiring harness.
- With the new sensor installed properly and securely, you can now replace the wheel back onto the car, tightening the lug nuts with your lug wrench.
- Lower the car back down onto the ground using the jack, and remove the jack stands.
- Lastly, perform a simple test to ensure everything is working correctly. Start your car and observe whether the brake warning light has been reset.
Top BMW 745i Brake Pad Sensor Brands for Sale
Starting with Bowa, this manufacturer is acclaimed for its top-of-the-line automotive sensors, including BMW 745i brake pad sensors. They prioritize innovation and extensive research in their production process, delivering solutions that increase the safety and efficiency of vehicles. Their products are known to uphold high standards of quality, reliability, and longevity.
Moving on to Genuine BMW, this brand represents the pinnacle of automotive parts manufacturing, representing the purity of the original equipment intended for the BMW 745i brake pad sensor. These parts, as indicated by the term 'Genuine', are produced by specifically selected manufacturers trusted by BMW themselves. This assures drivers of an unparalleled match in terms of fit, performance, and durability to what was initially installed on their BMW 745i at the factory. These parts encapsulate the essence of luxury and performance, synonymous with the BMW branding.
Lastly, there's Sadeca, a Spain-based company specializing in braking system components. They have garnered prestige over the years for their meticulous industry standards. Their brake pad sensors for the BMW 745i demonstrate these high standards, offering efficient service and impressive durability. Sadeca takes pride in its rigorous testing procedures and strict quality control, ensuring the components they produce stand up against the harshest conditions while maintaining optimal performance.
Find Great Deals on BMW 745i Brake Pad Sensor
At AutohausAZ, we value quality and customer satisfaction. One of the reasons customers prefer shopping with us for their BMW 745i brake pad sensor needs is the superior quality of our products. Our sensor components are supplied by leading parts manufacturers, ensuring that each piece meets rigorous industry standards.
Another advantage lies in our highly competitive pricing. We firmly believe in providing our customers with the best deal possible and strive to keep our prices as affordable as we can. This approach not only ensures that our customers receive the best value for their money but also allows them to maintain their vehicles without breaking the bank.
Additionally, we understand that shopping for auto parts can be confusing or even overwhelming for some people. To address this, we have designed our website to be user-friendly and informative. Each product listing provides all the necessary information so that our customers can make an informed buying decision.
Further augmenting the shopping experience, we pride ourselves on our exceptional customer service. When shopping with us, customers have access to professional guidance and support. Whether they need help selecting a brake pad sensor or have technical queries about a product, our team is always ready to provide prompt and courteous assistance.
Lastly, we have a straightforward and hassle-free return policy, providing customers with peace of mind knowing that if, for any reason, a product does not meet their expectations, returning it is a simple process.
In conclusion, when shopping at AutohausAZ for a BMW 745i brake pad sensor, customers can expect high-quality products, competitive pricing, a user-friendly platform, exceptional customer service, and an easy return process.
